118-02襯墊-可印刷，柔性，絕緣涂層

說明：118-02是一種適用于移印的柔性電絕緣涂料。

噴霧、浸漬和注射器分配。本產品對卡普頓、聚酯薄膜、玻璃、塑料

以及其他各種表面。與傳統絕緣材料不同，這種產品非常抗彎曲。

還有折痕。有些應用包括，但不限于，帶狀電纜，聚酰亞胺柔性。

電路，聚合物厚膜電路和薄膜開關。

典型固化特性：

粘度（cps）10000-12000

抗皺性佳

體積電阻率（Ω-cm）1.1 x 1014

介電強度（伏特/密耳）1300

損耗因子（100赫茲）0.013

介電常數（100赫茲）4.2

水汽透過率低

建議在使用前充分?jǐn)嚢韬凸袒?18-02已準備好用于噴涂

和/或浸涂。可通過添加CMI 114-20（緩慢干燥）或113來實現額外的稀釋-

39（快干）稀釋劑。當在130℃下固化5分鐘時，大多數應用的性能良好。良好

通過在25°C到175°C的溫度范圍內固化，也可在各種基底上獲得性能。

注：使用低溫固化劑時，應加入1PHR B-187催化劑。建議使用B-187

高度耐化學性。建議終用戶通過實驗確定溫度和時間

適合個人應用。

貯存期：25℃下保存3個月；5℃下保存6個月，-10℃下保存12個月

安全和操作：在通風良好的情況下使用。遠離火花和明火。避免

長時間接觸皮膚和吸入蒸汽。用肥皂和水清洗皮膚。保留

容器關閉以避免污染。如果冷凍儲存，允許容器加熱至室溫，以及

打開前*擦掉所有冷凝水。

118-02襯墊-可印刷，柔性，絕緣涂層

 118-02
PAD- PRINTABLE, FLEXIBLE, DIELECTRIC COATING
DESCRIPTION: 118-02 is a flexible, electrically insulating coating suitable for application by pad printing,
spraying, dipping and syringe dispensing. This product features excellent adhesion to Kapton, Mylar, glass,
and a variety of other surfaces. Unlike conventional insulating materials, this product is very resistant to flexing
and creasing. Some applications for 118-02 include, but are not limited to, ribbon cables, polyimide flexible
circuits, polymer thick film circuitry, and membrane switches.
TYPICAL CURED PROPERTIES:
 Viscosity (cps) 10,000 - 12,000
Crease Resistance Excellent
 Volume Resistivity (Ω-cm) 1.1 x 1014
 Dielectric Strength (volts/ mil) 1300
Dissipation Factor (100 Hz) 0.013
Dielectric Constant (100 Hz) 4.2
Moisture Vapor Transmission Low
SUGGESTED HANDLING & CURING Stir well before using. 118-02 is ready to use as supplied for spray
and/or dip coating. Additional thinning may be accomplished by adding CMI #114-20(slow drying), or#113-
39(fast drying) thinner. Good properties for most applications result when cured of 5 minutes at 130°C. Good
properties are also obtained on a variety of substrates by curing at temperatures ranging from 25°C to 175°C.
NOTE: Add 1phr B-187 catalyst when using low temperature cures. The use of B-187 is suggested to impart a
high degree of chemical resistance. End user is advised to experimentally determine temperature and time
best suited for individual applications.
STORAGE: Shelf Life: 3 months at 25°C; or 6 months at5°C: or 12 months at -10°C
SAFETY & HANDLING: Use with adequate ventilation. Keep away from sparks and open flames. Avoid
prolonged contact with skin and breathing of vapors. Wash with soap and water to remove from skin. Keep
containers closed to avoid contamination. If stored frozen allow containers to warm to room temperature, and
thoroughly wipe off any condensation before opening.